1. Which tool to use when
Each tool answers one question that a farmer asks at a different point in the year. Used together, they describe the same farm from four directions.
🌡️ Before every drying batch
Drying & moisture. You know the fresh weight and the moisture you need; the tool tells you the finished weight, the water you have to remove, and how much rack space that batch needs. Use it to size a dryer or to check whether a filled rack can actually finish in the sun available.
🐓 Before quoting a feed buyer
Feed inclusion. A buyer wants a protein level at a price. The tool models the blend, checks the required inclusion against the fibre-driven ceiling for the species, and compares the two ingredients on cost per kilogram of crude protein — the comparison that decides whether leaf meal wins the business.
🌧️ Before the wet season arrives
Wet-season planner. Your cut schedule and your rainfall pattern together decide which harvests can be sun-dried and which cannot. The tool counts them, works out the daily throughput they demand, and shows what happens when the drying window shrinks to a day.
🌱 Before promising a fertility plan
Compost mix & pile size. An application rate per hectare is a small number; the pile that produces it is not. The tool splits your two feedstocks to hit a C:N target, then reports the raw tonnage, the water and the volume you have to find room for. See compost in the soils chapter.
Several of these build on figures published elsewhere on the site: drying targets and rack depths in drying, moisture limits in moisture & water activity, inclusion ceilings in feed inclusion rates, cut intervals in pruning & canopy management, and application rates and compost practice in soils, compost & fertilizer. If you change a figure in a chapter, change it here too.
2. Drying & moisture calculator
Fresh malunggay leaf is mostly water, and the ratio between what you harvest and what you can sell is set by two numbers: the moisture in the leaf coming in, and the moisture you allow in the finished product. Everything else — fuel, time, rack space, labour — follows from the water you have to remove.
Type the fresh weight of the batch and the moisture figures, and the finished weight, the water to be removed and the rack area appear below.
The figures here are wet basis — water as a share of the total weight, which is how moisture meters and oven tests are normally reported for food. A "dry basis" figure (water as a share of the dry matter) is always the larger number and is a common source of confusion when comparing a laboratory report against a quoted target. Ask which basis a number is on before you use it.
3. Feed inclusion calculator
Leaf meal sells to feed buyers as a protein source, so the negotiation is almost always about protein level and price. This tool answers both halves: what inclusion rate reaches a protein target, and whether that ingredient is actually the cheaper protein.
The blend appears below as you type.
Blend
A ration is not defined by crude protein alone. Fibre caps how much leaf meal an animal can use, amino-acid balance decides whether the protein is any use, and digestibility decides how much of it ends up in the animal. Use this tool to see whether a target is even reachable inside a credible inclusion rate — then run a pen trial and let the feed conversion ratio answer the real question.
4. Wet-season drying planner
This is the tool that most often changes a plan. A moringa farm does not fail because it cannot grow leaf; it fails because in a wet month the leaf it grows cannot be dried before it spoils. Count the harvests that fall in the rain, work out the daily drying throughput they require, and the case for a covered dryer becomes arithmetic rather than optimism.
Put in the fresh leaf a single cut produces, and the planner counts the cuts that land in the rainy window and the drying capacity they demand.
- Shorten the cut interval in the wet months, so each harvest is smaller and can clear the rack faster — at the cost of more cuts and more labour per kilogram.
- Sell those cuts fresh instead of drying them. A wet-season cut has a market in the nearest palengke or in institutional kitchens; see the fresh-market chapter.
- Move the wet-month product sideways into feed or into animal use, where moisture requirements differ from food-grade powder. See leaf meal for feed buyers.
- Buy or build covered capacity — a solar dryer or a mechanical unit sized to the throughput figure above, not to the annual average.
5. Compost mix & pile size calculator
Composting advice is usually given as a rate: spread five tonnes to the hectare, or a bag of compost per square metre. This tool works backwards from the area you want to cover to the material you actually have to gather, because the gap between the two is where fertility plans fail — an application rate of a few kilograms per square metre becomes a pile measured in cubic metres.
Enter the area you intend to amend and the rate you intend to use. The defaults are a square metre-rate that comes out at about five tonnes to the hectare, which is the figure the soils chapter quotes.
The C:N split is a two-feedstock blend on a dry-matter basis — the same algebra as any mixing problem. Real piles are built from whatever is at hand, in layers, by feel, and an approximate ratio within a point or two of target still heats properly. What the number does decide is scale: you cannot quietly compost five tonnes of finished product out of a single bin, and the volume figure is the honest answer to "how much space does this take".
6. What these tools do not know
Calculator output is arithmetic. Every number below is a modelling assumption, and the honest way to use the tools is to change the assumptions until the answer stops being comfortable.
| Assumption | Where it can mislead you |
|---|---|
| Moisture behaves as a single mixed mass | Real batches have wet and dry layers, thick stems and thin leaf. A batch can average on target and still have pockets that will mould. Sample properly, and dry by layer depth rather than by total weight. |
| Drying is a pure water-removal calculation | Air flow, humidity, temperature, leaf thickness and rack depth decide how long drying actually takes. The planner sizes the job; it does not forecast your dryer. |
| Cuts land evenly on a fixed cycle | Weather, labour, festivals and storms all move a harvest. A cycle that does not divide into 365 days also slides against the calendar, so the rainy-month count changes from year to year. |
| Rainfall follows the simplified climate types | Corona types are a national pattern. Your valley, your mountain and your province's actual rainfall record are the authority — the same point the regional chapter makes. |
| Protein blending is linear | It ignores fibre, amino-acid profile, digestibility and palatability. Species ceilings used here are published planning ranges, not guarantees for your animals. |
| Prices are whatever you typed | The tools take prices as inputs because local prices differ by month, by province and by buyer. Any conclusion about which ingredient is cheaper lasts exactly as long as the figures do. |
| Feedstock C:N ratios are single numbers | Real materials vary with age, species and moisture: rice straw is not one ratio, and neither is manure. The compost tool works from the two ratios you give it because it cannot sample your pile. Treat its output as a starting blend and correct by smell, heat and squeeze. |